Auto Tune Kit for Power Commander V Harley Davidson Models A dual O2 sensor version made specifically for Harley Davidson models. It comes with two O2 sensors two control modules CAN connection cables and custom length sensor cables. It also includes a built in power connector that plugs directly into the bikes wiring harness for easy connection.
Part Number: PCAT-100 MSRP: CAN$738.98 Price: CAN$629.13
Auto Tune Kit for Power Commander V Universal Fit A universal fit single O2 sensor kit. It can be used on any vehicle that has a PCV installed on it. It comes with a single O2 sensor cut to length sensor cable control module O2 sensor weld on bung and CAN connection cable. It requires a ground and 12 volt connection be made using the supplied Posi-Taps.
Part Number: PCAT-200 MSRP: CAN$519.28 Price: CAN$441.38
Ignition Module for Vulcan 2000 - Not for use in California - Allows user to advance or retard the ignition curve based on throttle position and rpm and to tune each cylinder individually.- Ignition module connects to PCIII USB via a built-in expansion port link.- Connects to the ignition coils through an intermediate harness connection or directly to the coil connectors no cutting or splicing of wires is required.- Direct coil driver technology allows a high degree of flexibility in timing adjustments.
Part Number: 6-20 MSRP: CAN$708.94 Price: CAN$603.16
Part Number: 3107 MSRP: CAN$129.72 Price: CAN$111.83
Oxygen Sensor eliminator kit for CA Models Each Required for California and some European Honda models that have oxygen sensors. The kit disables the closed loop system for racing use.The system is designed to read the Oxygen sensor under certain conditions and temporarily change the airfuel ratio. The closed loop circuit has a very limited operating range which is only in effect while holding a steady speed at certain rpms and throttle positions. In this limited area the stock system with or without the Power Commander will gradually and temporarily lean out the air fuel ratio in an attempt to achieve an airfuel ratio of 14.7:1 stochiometric.The Oxygen sensors can be disconnected but this will trip the F.I. dash warning light.
Part Number: 76423005 MSRP: CAN$35.85 Price: CAN$30.48
Part Number: PC403-411EX MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII - 00-01 Victory V92SC - Not for use in California The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC904-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII - 03-07 Victory Vegas - Not for use in California The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC909-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII - 05-06 Victory HammerKingpin - Not for use in California The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.html targetblankCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.More Information:A HREFhttp:www.powercommander.comfeatintro.shtml TARGETnewIntroduction Aby PowerCommander.comA HREFhttp:www.partsmag.comspring2001vol8issue2dynojet82dynojeteditorial82.html TARGETnewProgramming the Perfect Power CommanderA by Partsmag.com
Part Number: PC921-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII - 99-01 Victory V92C - Not for use in California The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC901-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII - Road StarWarrior 02 to 08 - Not for use in California The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.A HREFhttp:www.partsmag.comspring2001vol8issue2dynojet82dynojeteditorial82.html TARGETnewProgramming the Perfect Power CommanderA by Partsmag.com
Part Number: PC403-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 02-03 VTXRNF 02-04 C - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC109-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 04 up VTX 1800NRF 05 up VTX 1800C - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.Note: CA models require the Oxygen Sensor Eliminator Kit sold separately.
Part Number: PC122-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 04-07 Vulcan 2000 - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC211-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 1200 Sportster 07 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC817-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - 1500 Drifter - Not for use in California This is the new improved USB version of the PCIII. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC201-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 1500 Mean Streak - Not for use in California This is the new improved USB version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC205-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 1600 Mean Streak - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC215-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 1600 Nomad - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC220-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - 883 Sportster 07 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC816-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - Bonneville 2008 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC519-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Boulevard C50M50 05 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC322-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Boulevard C90SE 05 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC323-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Boulevard M109RC109R 06 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC330-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Dyna Models 2006 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC811-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - EFI Dyna Models 04 to 05 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC810-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - EFI Dyna Models 07 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC814-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - EFI Softail and Duece 01 to 06 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC805-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - EFI Softail Models 07 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC813-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - EFI Touring Twin Cam Models 2007 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC812-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - EFI Touring Twin Cam Models 2008 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC818-511 MSRP: CAN$758.87 Price: CAN$645.11
PowerCommander PCIII USB - EFI Twin Cam Touring Models 02 to 06 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC807-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - EFI Twin Cam Touring Models 99 to 01 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC802-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Evo Touring Models 97 to 98 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC801-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Marauder 1600M95 04 to 05 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC318-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Nomad 1500 Fi - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC202-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Raider 2008 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC435-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Road Star 2008 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC431-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - RoadlinerStratoliner 06 to 08 - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC417-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - SpeedmasterAmericaScrambler 2008 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC520-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - V-Rod Models 02 to 06 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC809-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - V-Rod Models 2007 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC815-511 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - V-Rod Models 2008- Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC819-511 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCIII USB - Vulcan 1500 Classic Fi - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC203-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - Vulcan 1600 Classic Fi - Not for use in California This is the new improved USB Version. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC209-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB - XV1300 07 to 08 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC424-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCIII USB for VN900 - Not for use in California This is the new improved version with a USB port instead of a serial port. The PC is a fuel injection and ignition timing on some models adjustment unit that plugs inline with the bikes stock ECU. The PC uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the PCs onboard microprocessor. a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander aUsing this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes ECU electronic control unit. Removing the PC returns the bike to its previous stock condition. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
Part Number: PC225-411 MSRP: CAN$718.93 Price: CAN$611.15
PowerCommander PCV - 1200 Sportster 10 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2010 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-010 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - 1200 Sportster 2009 - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-002 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - 883 Sportster 2009 - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-001 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - BonnevilleT100Thruxton 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC21-005 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Boulevard C50SE and M50 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC20-014 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Boulevard C90SE 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC20-015 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Boulevard M109RC109R 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC20-016 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Boulevard M90 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC20-018 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - BRP Can-Am Spyder 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC25-004 MSRP: CAN$798.82 Price: CAN$679.06
PowerCommander PCV - BRP Can-Am Spyder 990 RTRTS 11 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC25-010 MSRP: CAN$990.56 Price: CAN$842.84
PowerCommander PCV - Dyna Models 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-005 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Honda Fury 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC16-014 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Honda VT750C 09 and newer European Models Only The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC16-011 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Raider 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-013 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Road Star 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-010 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Road Star Warrior 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-011 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - RoadlinerStratoliner 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-012 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Softail DeluxeHeritage 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-007 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Softail Models ex. DeluxeHeritage 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-004 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - SpeedmasterAmericaScrambler 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC21-006 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - Touring Models 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-003 MSRP: CAN$758.87 Price: CAN$645.11
PowerCommander PCV - Touring Models 2010 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-011 MSRP: CAN$758.87 Price: CAN$645.11
PowerCommander PCV - Triumph Thunderbird 1600 10 and newer - Not for use in California The New Power Commander V is loaded with tons of new features.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC21-001 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - V-Max 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-003 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - V-Rod 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-006 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - V-Star 950 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-009 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - VT1300 Stateline Interstate Sabre 10 and newer - Not for use in California Not for use in California.The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.ba hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abbFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC16-025 MSRP: CAN$798.82 Price: CAN$679.06
PowerCommander PCV - Vulcan 900 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC17-015 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV - XR1200 Sportster 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC15-008 MSRP: CAN$738.9 Price: CAN$480.29
PowerCommander PCV - XV1300 09 and newer - Not for use in California The New Power Commander V is loaded with tons of new features. It is compatible with 2009 and newer bike models.a hrefhttp:community.cruisercustomizing.comPower-Commander-Map-Tip-of-the-Week-from-Cruiser-Customizingblog21672822960.htmlCheck out Kyles Tip of the Week and learn how to map your new Power Commander abFeatures:b Reduced size from PCIIIusb less than half of the size of PCIII USB powered from computer 9 volt adapter is no longer needed for programming 2 position map switching function built in map switch not included Gear input allows for map adjustment based on gear and speed Analog input allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables. Unit has a -100250 fuel change range up from -100100. This allows more adjustment range for 8 injector sportbikes 10 throttle position columns up from 9 on PCIIIusb Enhanced accel pump utility increased adjustment and sensitivity ranges
Part Number: PC22-018 MSRP: CAN$738.9 Price: CAN$629.13
PowerCommander PCV W Dual O2 Optimizers- BRP Can-Am Spyder RTRTS 2010- Not for use in California The Power Commander V PCV is the state of the art fuel injection management system for late model fuel injected machines. PCV installs easily to your factory wiring harness using OEM style connectors - no splicing or soldering is required some models require tapping into a wire with the included tap. PCV uses the latest CAN-BUS technology for lightening quick communications and ultra precision control and is less than half the size of the PCIIIUSB Once installed you provide your machine with a map to reconfigure your fuel injection operation. PCV can create a separate map for each cylinder for each gear and for each injector requires optional accessories see below Dozens of maps are available varies by machine from Power Commander.com or you can visit a local Authorized Power Commander Tuning Center like Orient Express and have a custom map built for your specific machine on the dyno PCV allows you to store 2 maps on the unit accessible with optional map switch. The maps smooth your airfuel ratio to improve throttle response drive-ability and power. You may also see improvements in fuel economy and sound quality from your machine. From the factory a stock machine has lean spots and rich spots to meet Federal noise and emissions regulations. These high and low areas of your RPM range can be felt with jerky or snatchy throttle response and irregular acceleration and surging at a steady throttle position while cruising down the highway. The PCV cleans up the majority of your fuel injection issues at a very affordable price Have you modified your machine with a high performance exhaust intake or engine work The PCV makes it easy to tailor your fuel injection to take advantage of these changes. Hundreds of models thousands of customers millions of horsepower The PCV also provides easy expandability multi function hub is built in with the optional extras like: Quick Shifter allows full throttle clutch-less upshifts Secondary Fuel Module for control of 4 upper injectors on
Part Number: PC25-006 MSRP: CAN$896.79 Price: CAN$762.95
Part Number: 8733 MSRP: CAN$329.45 Price: CAN$281.6
Wideband Commander 2 - Powersports Base Unit The Wide Band 2 Includes the Following:1 Wideband 2 Module1 Data Acquisition Cable optional with 15-7011 kit1 Bosch LSU 4.2 Wide Band Oxygen Sensor1 Oxygen Sensor Cable1 Oxygen Sensor Weld Bung Plug and Copper Washer2 Dynojet CAN-Link Port Seal3 Wire T-taps1 Terminal Strip Plug2 Dual Lock Strips1 Alcohol Swab3 Zip Ties1 Warranty Registration Card2 Dynojet Decals1 Installation InstructionsWide Band 2 Options:Dynojet LCD Full Color Touch Screen DisplayWhite or Black Analog Gauge 52mm 2 116White or Black Digital Gauge 52mm 2 116Data Acquisition Gauge Combination HarnessDynojet CAN-Link CablebWide Band 2 Technical Features:b0-5v Calibrated Analog AFR Output Connects to external data acquisition deviceOne wire RPM hookup0-5v analog input TPS MAF boost etcBuilt-in Sensor Condition TestDurable enclosure and wire sheathing for years of trouble-free operationDynojet CAN-Link communication allows for expansion optionsbWide Band 2 Product Specifications:bPower Requirement 11.5 - 15 VDC 3ADimensions 2.80w x .56h x 1.488dRange: .68 lambda - ambient airbInputs:b Analog: 0-5 VDCDigital Square wave 0 - 12 V nominal coil - tachometer signalbOutputs:bGauge Driver 0 - 5 VDC analogCalibrated AFR 0 - 5 VDC analogSimulated Narrow BandDynojet CAN-Link accessory cable requiredbNote:b Requires Gauge Kit
Part Number: PC15-7011 MSRP: CAN$497.33 Price: CAN$423.41
¿POR QUE COMPRAR NA CRUISERCUTOMIZING.COM?
Oferecemos-lhe uma experiência de compra segura verificada pela McAfee, líder em segurança, opções de entrega gratuita, devoluções sem complicações e um serviço de atendimento ao cliente de alta qualidade.
